How To Hang A Skateboard Deck On The Wall

How To Hang A Skateboard Deck On The Wall

Well, if you genuinely love your skateboards, you might need to have some haven for them. For those reasons, you might like to hang it on your wall in your home. There are a lot of reasons why you should do it, either you want to showcase your favorite one or to retire your old decks. Moreover, hanging them on the wall can help you organize your deck. So, we have some DIY projects that you might like or can help you to hang your skateboard decks on your wall.

Hanging by the Use of Hooks

Image Source

Things you needed:

  • Wall hooks
  • Fishing lines
  • Pencil
  • Ruler
  • Scissors
  • Double size tape

The essential thing that you need to do this is your sharp scissors. As you need a lot of cuttings through your fishing net and your tapes. Make sure also that the tapes you provide can stick for a long time in the back of the hooks and the surface of the wall. Otherwise, your deck will surely fall.

Step 1: Putting the Tape

Put a double size tape through the back of your hooks. Remember, make sure that it has good stress on it to bear or stand the weight of your skateboard for a long time.

Step 2: Drawing

It would be best if you used a ruler and pencil to draw a line on your wall. Remember also that the line you draw is parallel to the floor. Moreover, make sure that the distance of the line your draw to the floor should be high enough to hang your decks. The line should be around 900mm or ¾ and the full length of your skateboard. Then, you should mark the two ends you drew as well as the center of the lines. These markings will point out where you want to put your hooks on.

Step 3: Sticking the hooks on

After you finish with the 3 points you drew, stick each of the hooks on the points. As you attach the hooks on each end, make sure that it is straight. It will help your skateboard to hang correctly on the hooks.

Step 4: Inserting the Fishing Line

In this step, you will find it very simple to do. You’ll need to put the fishing lines through the bottom holes in the gripe area of your skateboard. After, you’ll need to strengthen the knots and, finally, cut the excess lines with your scissors.

Step 5: Hang your Skate on it

If you finish, hang your skateboard on the hook through the knot. Then boom, you have now your DIY skateboard wall hanger.


Hanging With The Use Of Only Two Screws

Image Source

Things you need:

  • 2 Long Drywall Screws
  • Electric Drill
  • Ruler
  • Pencil

A simple way to hang your skateboard decks through your walls with only two screws. With only just a pair of two drywall screws, you can proudly showcase your skateboard decks in your room.

Step 1: Removing the Trucks

In this method, you need to remove the trucks of your skateboard. Then measure the two holes from the hardware of your deck as it will be your guide for the two screws and mark it with a pencil.

Step 2: Drilling the Screws

After you mark the two holes, drill it with two long drywall screws by the use of an electric drill. Make sure that it doesn’t go too far, or else your deck will fall if you hang it.

Step 3: Hanging Your Skateboard

After you finish screwing the two screws, you can now hang your skateboard deck on your wall. There is also a way of hanging your skateboard deck on your wall with the use of 2 drywall nails. It is the same process needed like this method, but you’ll need a hammer to stick the nail on your walls.

RECOMMENDED VIDEO FOR YOU…….


Using A PVC Water Pipe

Image Source

Things You Need:

  • 3-inch diameter schedule 40
  • 2-inch drywall screws
  • Hack saw
  • Electric drill with 3/8 and 3/16 drill bits
  • Ruler

This method is also a simple way to hang your skateboard decks through your walls. This method only supports the wheels of your skateboard.

Step 1: The Cutting Process

You should be careful about cutting the PVC pipe when you are using power tools and follow the safety precautions. First off, cut the pipe in half with a hack saw around 8 inches for a standard skateboard. Then, it would be best if you slipped the pipe in half lengthwise.

Step 2: Drilling

After you finish the cutting process, you need to drill 2 3/8 inch holes right in the center of the pipe from top to bottom. It requires 4 inches apart as it will serve as the corners of the notch that you need to cut for the next step. Then, you need to drill another two holes with 3/16 inch holes from the center, from right to left. It should be ½ inch on edge and another one or ¼ inches through the same edge.

Step 3: Notch Cutting

In this step, this is your final process for your DIY wall hanger. It would help if you cut a notch through the center for your trucks. The cut you’ll do also depends on the style of your trucks, whether it’s a venture, gullwing or independent. Right in the opposite of the mounting holes, you need to cut the edges on the large hole and do it once again on the 2nd large hole. Cut it down the length between the two large holes by using a hack saw.

Step 4: The Final Step

After you finish cutting the base, you need to hang it on your wall. You need to use drywall screws, about 2 inches, which are good if you have a wooden wall. If you have a concrete wall, you can use Tap-Con screws. After you hang it on the wall, you are ready to hang your skateboard deck on it.

Well, hanging your decks on your wall is a simple way to do. It doesn’t consume time or even your effort. Although one advice is to use your tools safely, all in all, we hope that all the mentioned above can be helpful.

Leave a Comment

Your email address will not be published. Required fields are marked *